SSDs are faster, more stable, and less energy consuming than older HDDs, but even SSDs do not have an indefinite lifespan and may take several years. Use problems. Therefore, it is a good idea to identify what indicates a SSD memory failure in your system before you experience a memory crash or data loss.
How do SSDs fail?Unlike HDD hard drives, SSDs do not have physical rotating disks, so their problems and failures are different from older hard drives. While the memory component of SSD drives is not said to be mechanically damaged, other components may have such a problem. Especially in cases where the transmitted power fluctuates or is suddenly cut off. In fact, in the event of a power outage, even the data in these memories may be damaged, even if the SSD drive itself is not fully operational.
Another problem that is predicted for these memories is this. That they have a limited reading/writing cycle; A problem that affects all types of flash drives. So there is no room for fear and anxiety. In fact, if you have purchased an SSD in the last few years, you should not worry too much about reading/writing restrictions; Because research shows that newer SSDs are less vulnerable than older models.
However, the data read/write cycle will affect your ability to write data to the SSD drive. As long as you can read the information, you can retrieve it. But it's still not bad to know if your SSD is nearing the end of its life so you can replace it with a new drive in time.
How to check the health of your SSDs?
Windows operating system users can use CrystalDiskMark software to check the health of their system SSD memory. A convenient option for macOS users is to use Smart Reporter Lite, and Linux users can also use the Hard Disk Sentinel. But in addition to these software, there are various symptoms that can be considered signs of SSD memory failure.
1. Errors containing Bad Block
Like the bad sector on older hard drives, SSDs also have a meaning We are facing a bad block. This means that the computer tries to write down and store the information, but it takes a long time and eventually the operation fails, resulting in an error message.
Common bad block cues can be: Notes the following:
- The file is not read or written to the drive.
- The system needs to be repaired.
- Active programs often freeze They may or may not run.
- You will encounter consistent errors when transferring files.
- In general, and especially when accessing large files, the system will run slowly. li>
If you notice any of the above symptoms, it is best to use one of the available software to check the health of your drive. If a problem is found, it is best to back up your files and data first, and then try to replace the current drive with a new SSD drive.
2. Files are not read or written
bad block can affect your files in two ways :
- The system detects a bad block when writing data to the drive and then refuses to write the data.
- The system detects a bad block after writing the data and then Refuses to read data.
If the first scenario occurred, your data was never written, so it was not damaged. Usually the system will fix this problem automatically, but if it did not or could not, you should probably fix the problem by storing the data elsewhere or copying it to the cloud and restarting the computer and then re-saving it to the drive being used.
Unfortunately, the data will not be recoverable if the second scenario occurs. Of course, you can try ways to recover data from a bad SSD, but you should not expect too much from them. Bad block usually means that the data in that block is lost.
3. File system needs repair
Ever on any Windows or macOS operating system An error warning like the one above has appeared on your screen? Sometimes this can happen because the computer does not turn off properly. Otherwise, it could be a sign of a bad block or a problem with the drive port.
Fortunately, the solution is simple. Windows, macOS and Linux are equipped with corrupt file system repair tools. For such an error, each operating system directs you to the appropriate tool so that you can take steps to repair the file system.
However, some information may be lost during this process and it may be very difficult to recover it. Be. Therefore, it is best to back up your files periodically.
Consecutive crashes during boot
If you encounter a crash while booting the computer, but then Resetting the problem several times will fix the problem, you should be suspicious of your SSD drive. This may be due to a bad block or even a sign that the drive is ending, so it's a good idea to back up your data before anything worse happens.
Check for cracks due to a problem with the drive Or not, you can download and install one of these diagnostic tools. If you have backed up your data, you can format the drive and reinstall the operating system.
5. SSD memory turned into a read-only drive
This problem is not very common, but some Users experience it. Your SSD drive may prevent any operations that involve writing data to disk, but it will still operate in Read-only mode. This drive is considered a lost drive for doing anything, but fortunately even in this case the data can be recovered.
Before the SSD drive that you think is damaged is gone Drop it, try connecting it to your computer as an external hard drive or secondary drive. Before doing so, make sure that your computer operating system does not boot through this drive. If you still encounter Read-only mode after using it as an external or secondary drive, you can recover the data first and then format the SSD drive.
How to extend the life of your SSD memory
If your system's SSD memory is experiencing a lot of problems and you recognize that it is nearing the end of its life, or if you have been using it for many years, this is the best and safest way to protect your data. Replace the current drive with a new SSD drive. At the same time, you can consider a few steps to extend the life of your drive:
- Do not expose the drive to excessive temperatures and equip your computer with a suitable cooling system./li>
- Try to keep the system away from any fluctuations, outages or any other electrical failures.
- Have extra free space on your SSD drive so that it can move data from bad blocks.
If you are looking to replace your system SSD drive, we recommend using the M.2 SSD, which performs faster than the mSATA standard.
- How to RAM Optimize your computer for maximum performance?
Source: Make Use Of